Product Guide
Business Music
Technical Library
Installations
Software Downloads
SIA-Smaart Web Site
Pressroom
International Newsletter
Photos
Tunings
FAQ 
Search
Customer Service
Sitemap
About Us
Contact Us 
Employment
Links
 
MPA Series Amplifiers MPA Series Owner's Manual

MPA Series Brochure



The MPA Professional Audio Amplifier Series is specifically matched to the characteristics of JBL speakers.

  • They deliver a wide range of output power to accommodate even JBL's most powerful transducers.
  • They exhibit good peak power capability and excellent dynamic headroom to accurately reproduce musical transients.
  • Each amplifier includes a protective output limiter to protect both the amplifier and the loudspeaker form excessive power.
  • The limiting action curve is perfectly matched to JBL transducers taking full advantage of their low power compression characteristics.
  • The action of the limiter does not "rob" the system of acoustic power since the total output of a heavily distorted amplifier is the same as the "limited" MPA amplifier, but with extremely clean, non-distorted sound.
  • Open Input Architecture™: JBL systems philosophy also extends to the input stage of the amplifier. Flexible input cards allow these amplifiers to be tailored to a variety of applications, and configurations can be changed easily as new situations arise.
SPECIFICATIONS
 
RATED OUPUT POWER**: MPA1100 MPA750 MPA600 MPA400 MPA275
4 Ohm/Ch:
1200 W* 800 W 660 W 400 W 275 W
8 Ohm/Ch:
820 W* 550 W 440 W 275 W 175 W
8 ohm bridge:
2400 W* 1600 W 1320 W 800 W 550 W
MIDBAND OUTPUT POWER***:
2 Ohm/Ch:
1520 W* 1100 W 960 W 600 W 400 W
4 Ohm/Ch:
1320 W* 900 W 740 W 450 W 325 W
8 Ohm/Ch:
880 W* 600 W 480 W 300 W 200 W
Voltage Gain:
80 (38 dB) 63 (36 dB) 56 (35 dB) 45 (33 dB) 35.5 (31dB
Net Weight:
29 kg (64 lbs) 24.8 kg (55 lbs) 20 kg (44 lbs) 19.1 kg (42 lbs) 18.1 kg (40 lbs)
Shipping Weight:
31.8 kg
(70 lbs)
26.8 kg
(59 lbs)
22.2 kg
(49 lbs)
21.2 kg
(47 lbs)
20.4 kg
(45 lbs)
*Amplifier's output protective circuitry prevents full power output above 15kHz.

**Rated Power:  is minimum continuous sine wave output per channel, with both channels driving their rated load over a power bandwidth of 20 Hz to 20 kHz. Maximum total harmonic or intermodulation distortion measured at any power level from 250 milliwatts to rated power is less than 0.1%. Maximum Transient Intermodulation Distortion is less than 0.05%.

***Midband Power:  is maximum output per channel, with both channels driven, at onset of clipping with 1 kHz sine wave, THD 1%

   
Distortion: SMPTE-IM, less than 0.05%
Frequency Response: 20 Hz to 20 kHz, +0.1 dB, 8 Hz to 100 kHz, +0/-3 dB
Damping Factor: Greater than 200
Dynamic Headroom: 3 dB at 4 ohms (2 dB for MPA 275)
Noise: 100 dB below rated output (20 Hz to 20 kHz)
Sensitivity: 1 Vrms for rated power (8 ohms)
Input Impedance: 10 kOhms unbalanced, 20 kOhms balanced
Controls: Front: AC switch, Ch 1 & Ch2 Gain (2 dB detents). Rear panel switch for parallel inputs or bridged output configuration.
INDICATORS: (each channel)
Power: Green LED
Signal Present: Green LED
Level -20: Green LED
Level -10: Yellow LED
Clip: Red LED
Protect: Red LED (flashes for over-temp)
CONNECTORS: (each chan., except one stereo Speakon)
Input: Barrier strip and XLR
Speakers: 5-way binding posts, Speakon connectors, st. Speakon (for mating cable, use Neutrik NL4FC connector)
Cooling: Continuously variable speed fan, rear-to-front air flow
Amplifier Protection: Full short circuit (Output Averaging™ short circuit protection US Patent 4,321,554), open circuit, ultrasonic, and RF protection, thermal limiting, muting; stable into reactive or mismatched loads
Load Protection: On/off muting, clip limiting, DC-fault load grounding relay with internal fault fuses
Output Circuit Type: Complementary linear, high-efficiency outputs: 3-step on MPA1100, 2-step on MPA750, MPA600 and MPA400, 1-step on MPA275
Power Requirements: 100, 120, 230 Vac. 50-60 Hz
Power Consumption: (@ 120 Vac) Normal Operation: 4 ohms per channel
All models: less than 12 A, (1.44 kW)
Max. (full power, 2 ohms/channel): MPA1100, 41A (5kW); MPA750, 58A (7kW); MPA600, 32A (3.9kW); MPA400, 24A (2.9kW); MPA275 18A (2.2kW)
Dimensions: 48.3 cm (19in) rack mounting
45.5 cm (17.9in) deep (rear support ears)
MPA1100 & MPA750 are 13.3 cm (5 1/4in) tall (3 spaces); MPA600, MPA400 & MPA275 are 8.9 cm (3 1/2in) tall (2 spaces)
OPTIONS: (Input Modules)
IM-10 Two-channel, two-way crossover card provides multi-way active selectable frequency division with adjustable time delay for transducer alignment and equalization for both 2360 and 2380 horns
IM-11 18dB/octave sub-bass crossover card provides subsonic filter at 30 or 40 Hz, crossover frequencies of 80, 120 or 250 Hz with external highpass outputs
IM-12 Cinema crossover module features 24dB/octave filter slopes, crossover frequencies of 500 and 800 Hz, time delays for transducer offset alignment, horn equalization for 2360 and 2380 series horns and screen loss equalization
IM-30 Input connector expansion module provides parallel XLR and TRS 1/4" phone connector inputs and outputs


Copyright 2001 JBL Professional.
All rights reserved.